Carpet is a common tool to secure your rugs and carpets and remove sticky residue. This residue can attract dirt and make your carpet’s corner area look unsightly. Fortunately, there are several methods you can apply to remove rug tape residue from your carpet without causing any damage.
Let’s see details on rug removing services and their maintenance.
What is Rug Tape?
Rug tape is double-sided tape, which holds two sides of the component in order to ensure a secure sticking from both ends. A rug tape is used on carpet for the purpose of preventing slipping on your carpet or slipping, curling, or bunching up. This tape helps to hold your carpet on stairs, tiles, and laminated flooring, and also protects both the rug and the floor from damage.
What Tools Need to Be Removed Rug Stage?
Typically, you can remove rough tape using tools in three steps, like cutting & pulling, removing underlayment and tack strips, and for safety and cleanup. For cutting & putting, you can use a utility knife, locking pliers, and heavy-duty scissors. Also, removing underlayment and strips, use a pry bar, a floor scraper, and a hammer with safety gloves and knee pads.
Top 5 Essential Steps to Remove Rug Tag From Your Carpets
Removing a stubborn rug tag needs much patience and a careful approach to avoid damaging the carpet fiber. Please see the top 5 methods with directions better rug tape removing solution.
Read More: Commercial vs Residential Carpet Cleaning
Method-1 Pull Off as Much Tape as Possible by Hand
To remove rug tape from your carpet, start your hand to pulling off as much tape as possible. Work slowly and consistently, to avoid anything tearing into small or damaging any size with unmanageable pieces.
- Find the loose corners or edges of the tape before it starts removing.
- Grip the tape carefully using your thumb and forefinger.
- Pull the tape’s back side slowly at a sharp angle, which is close to the carpet surface. This technique helps you to minimize the pressure on the carpet fibers.
- If the tape tears, find another edge and continue within the same process.
- If you find the rug tape adhesive is too strong, you can use a non-damaging solvent to loosen it. Before using the solvent, you must try as much as possible by hand to pull it.
Method 2: Heat and Scrape Method, and Fit Your Carpet Fiber
After completing pull-off with the handy method, use the heat and scraper method, which is highly effective for dealing with tough, dried-on adhesive. The heating process loosens the adhesives, while the scraper is used for careful and precise removal without damaging your carpet.
- Use a hairdryer or a heat gun, aimed at the place with low heat, where you need to warm the rug tape. Move the head source back and forth within a small portion of the tape within 30-60 seconds.
- After heating, you’ll see that the adhesives will loosen from the source. Use a plastic scraper or a putty knife, which dulls the edge to softly scrape the tape and adhesive from the carpet fiber.
- Once you’re able to remove bulk tape from the carpet, check where is small portion of residue remains. In this case, you can use citrus-based adhesive remover or rubbing solution on a clean cloth. It helps you to remove spots softly to wipe out the remaining portion.
- Check as if both areas are removed, again use a dry cloth to remove if anything else remains in the carpet. Finally, use an air dryer to complete the process.
Method 3: Use of Dish Soap Solution to Remove Excess Moisture
You may be able to wipe out almost portion, but there are still small areas of surplus rug tape remaining on your carpet. Use a simple dish soap solution, which can be effective at removing the rest of the adhesives. This soft-removing method is good for avoiding hard chemicals that might damage your carpet fiber.
- Before you apply the solution, manually peel off any remaining pieces of rug tape to ensure the remaining adhesive is exposed.
- Take a small bowl, mix the warm water with a few drops of soft soap until the foam is ready to use.
- Now, dip a cloth or sponge into the solution, and dab it directly onto sticky but small residue. Ensure your solution is set for a few minutes to penetrate into the adhesive, and rub the area to remove the excess.
- Now use a clean cloth again to remove moisture with plain water, and wipe the tracking area to remove the identified area with soap solution.
- Spot the area with a dry towel to absorb excess moisture. Once your dry your carpet, vacuum the spot and restore texture.
Method 4: Use White Vinegar Techniques
White vinegar is considered a natural alternative solvent for stubborn adhesives without the use of hazardous chemicals. This acid effectively breaks down the sticky remaining and makes it easier to wipe from the carpet fiber.
- Manually start removing any loose pieces of rug tape and apparent adhesive that needs to be removed.
- Create a simple cleaning solution, and mix equal portions of white vinegar and warm water in a bowl.
- Use a vinegar solution to remove the surplus adhesive with a clean cloth. Keep the solution mixing for 5 minutes to ensure the acid breaks down the strong bond.
- Take a light brush or a clean cloth to softly scrub the area, and work with the excess out of the carpet fibers.
- Use a separate cloth moistened with clean water to wash the vinegar out of the carpet. Block the area with a dry towel to absorb all remaining moisture, and vacuum to restore carpet’s appearance.
Method 5: Adhesive Remover
This method is different from all other methods, specifically supporting with specialized professional services. These products are formulated to break down strong adhesives quickly, making this method a time-efficient choice for serious jobs.
- Start pulling off as much visible rug tape as you can by hand. This ensures the adhesive remover directly targets gummed extras on the carpet fibers.
- Apply a small amount of specialized product, Goo Gone, WD-40, which is designed carpet-safe adhesive remover, onto the remaining rugs. Trey to conduct a patch test on an obscure area that ensure no damage or discolor to your carpet.
- Use a clean, dry cloth or paper towel, softly block the targeted area. The adhesive should transfer from the carpet fiber onto the cloth. Repeat the same process with a fresh section of the cloth till the residue is completely removed.
Why You Should Choose Professional Tape Removing Services
In spite of having all other solutions, professionals are skilled and trained in mixing, treating, and understanding the complexities easily. When you think of self-maintenance, you may lose your valuable asset duration due to mishandling. Therefore, hire a commercial carpet cleaning service who will work with maintaining cleaning regulations & secure your assets.
Besides, training & skilled cleaning resources, professionals have adequate knowledge on mixing, and soft-touching abilities. This also saves your time and effort to remove rug tape from carpet without damaging the fiber.
FAQ
What is the Easiest Way to Remove Sticky Tape Residue?
Sticky tape residue depends surface and type of tape. Apply heat or soft adhesive with a solvent like rubbing solution, WD-40, or cooking oil to remove the residue.
Does Double-sided Rug Tape Ruin Carpet?
Before purchase, double-sided tape is designed for your carpets. As some rug tape looks the same but is designed to be used in hard flooring may cause damage to your carpet.
Does WD-40 Remove Carpet Glue
Yes, use distilled water, white vinegar, and dish soap, or WD-40 solution to remove the entire stain from your carpet.
Final Speech
Successfully removing rug tape ensures your carpet is secured from rug tape residue without damaging the carpet fiber. Though rug tape helps your carpet to set with any floor like tiles, wooden floor, or any other floor, from both sides. But changing position or cleaning the carpet has lots of difficulties, and solutions also.
You’re suggested to use or follow rug tape removing techniques through following self-effort or professional services. Experts suggest getting help from a professional for a smooth cleaning operation and save your time.